Is Your Press Brake Tooling Fully Staged?

You’ve likely heard of staged tooling. It’s one of the most effective ways to reduce setup time in a press brake operation. Fabricators use it when they have a bend sequence that requires several different tool profiles. 

Staged Tooling Reduces Setups and Runtime

Without staged tooling, an operator cannot complete a bend process in fewer than 8 steps. With staged tooling, the full sequence is completed in 3 steps. See the comparison below:

Without Staged Tooling   With Staged Tooling
1.     Install first tool set up 1.     Install full tool set up
2.     Pick up the part 2.     Pick up the part
3.     Make the first bend 3.     Complete the full bending sequence
4.     Put the part down  
5.     Change out the tool set up  
6.     Pick up the part  
7.     Make the second bend  
8.     Repeat steps 4–7 until part is complete  

As you can see, if you have a part that requires many bends, staged tooling saves a lot of time.

Equal Closed Height 

The key to staging is that all the tools in the process need to close at the same height. If the tools don’t close at the same height, the longer tools will collide and the shorter tools won’t engage. When the tools do have the same shut height, they can be loaded into the machine at the same time and the operator can do all the bending without ever having to put the part down or change the tools. See the diagrams below.

Can You Benefit from Staged Tooling?

Ask yourself the following questions to see if tool staging will improve your process:

How long is the part? A part as long as the brake is too long to make use of staged tooling. Any sequential bends will need to be set up separately. A part equal to or less than half the length of the brake can benefit from staged tooling with one tool set up on the left and one tool set up on the right.

How many different tool profiles are needed? The more profiles a bend sequence uses, the more beneficial tool staging will be. For example, a staged bend with two different profiles will result in a 50% faster process, but one with five different profiles will speed production by approximately 400%.

How many parts are bent and how frequently does it happen? The more parts in a run, and the more frequently this part run is performed, the more an operation will benefit from the elimination of multiple setups.

Does your machine accommodate staged tooling? Because a staged tooling sequence sets up the tools progressively along the brake, some of the bends will be done off center in the machine. Traditionally, machines work best when bending is done in the center because that is where forces are most balanced. Down-acting press brakes are often the most accommodating to off-center bending because they have mechanisms for compensating for tonnage to the left or right. Up-acting brakes are not as friendly, however, as they have mechanisms that shut the machine down if too much pressure is applied too far from the center. Up-acting press brakes can and do run staged tooling frequently but the bend lengths tend to be shorter.

Are You Getting the Best Staged Tooling for You?

You may not be getting the full staging benefits from your tooling. When you order tooling pre-staged from your vendor, you shouldn’t be limited to the same die and bend angle. When you order staged tooling from Wilson Tool, you can select tools of mixed angles, offsets, flattening varieties, gooseneck punches and different V openings, and they will all be of equal closed height. You should not be limited in your tool selection when ordering staged tools.

Wilson Tool offers all American and European style tooling pre-staged. This means that whatever profile or angle you require, it will be of the same closed height as your other Wilson press brake tooling.

To learn more about staged tooling, click here.

A Full Range of Clamping Options

Are you looking to streamline production while sticking to the confines of your budget? Take a look at how various hydraulic press brake clamping options can help you do just that in this article from Fabricating and Metalworking.

Read “Trends in Hydraulic Clamping Systems for the Press Brake” now.

 Follow Us on LinkedIn

LinkedIn

Stay up-to-date on the happenings at Wilson Tool and the sheet metal fabrication industry. We post technical articles, helpful solutions, new products, free webinars and more to our LinkedIn Company Page on a near daily basis. Don’t miss out! Go to our page and click the “Follow” button in the top right corner to stay on top of the latest news. Then comment on, like, or share our updates to keep your network informed.

See you on LinkedIn soon!

Save the Date!

Summer Brake School: Improving Bending Workflow

Dates: June 27 - 28 at Fox Valley Technical College in Oshkosh, WI

Join representatives from Cincinnati Incorporated, Greenheck Fan Corporation, Solidworks by Computer Aided Technology (CATI) and Wilson Tool for a 2-day training forum on improving press brake work flow. We’ll practice the following topics:

  • CAD programming as related to sheet metal
  • Programming at the press brake
  • Hands-on bending at an actual press brake
  • Lean press brake operations
  • Punch and die selection using bend limit graphs and air bend force chart
  • More efficient setups

This event is free to all Wilson Tool customers.

Learn More or Register